Product - FPGA

KU115

PYNQ-Z2

TUL PYNQ-Z2 board, based on Xilinx Zynq SoC, is designed for the Xilinx University Program to support PYNQ (Python Productivity for Zynq) framework (please refer to the PYNQ project webpage at www.pynq.io) and embedded systems development.

TUL PYNQ-Z2 Product Announcement (PDF)

TUL PYNQ-Z2 board, based on Xilinx Zynq SoC, is designed for the Xilinx University Program to support PYNQ (Python Productivity for Zynq) framework (please refer to the PYNQ project webpage at www.pynq.io) and embedded systems development.

TUL PYNQ-Z2 Product Announcement (PDF)

Product Specification


ZYNQ XC7Z020-1CLG400C
 • 650MHz dual-core Cortex-A9 processor
 • DDR3 memory controller with 8 DMA channels and
  4 High Performance AXI3 Slave ports
 • High-bandwidth peripheral controllers: 1G Ethernet,
  USB 2.0, SDIO
 • Low-bandwidth peripheral controller:
  SPI, UART, CAN, I2C
 • Programmable from JTAG, Quad-SPI flash,
  and MicroSD card
 • Programmable logic equivalent to Artix-7 FPGA
  • 13,300 logic slices, each with four 6-input LUTs
   and 8 flip-flops
  • 630 KB of fast block RAM
  • 4 clock management tiles, each with a phase
   locked loop (PLL) and mixed-mode clock
   manager (MMCM)
  • 220 DSP slices
  • On-chip analog-to-digital converter (XADC)
Memory
 • 512MB DDR3 with 16-bit bus @ 1050Mbps
 • 16MB Quad-SPI Flash with factory programmed
  48-bit globally unique EUI-48/64™ compatible
  identifier
 • MicroSD slot
Power
 • Powered from USB or 7V-15V external power source
USB and Ethernet
 • Gigabit Ethernet PHY
 • Micro USB-JTAG Programming circuitry
 • Micro USB-UART bridge
 • USB 2.0 OTG PHY (supports host only)
Audio and Video
 • HDMI sink port (input)
 • HDMI source port (output)
 • I2S interface with 24bit DAC with 3.5mm TRRS jack
 • Line-in with 3.5mm jack
Switches, Push-buttons and LEDs
 • 4 push-buttons
 • 2 slide switches
 • 4 LEDs
 • 2 RGB LEDs
Expansion Connectors
 • Two standard Pmod ports
  • 16 Total FPGA I/O (8 shared pins with
   Raspberry Pi connector)
 • Arduino Shield connector
  • 24 Total FPGA I/O
  • 6 Single-ended 0-3.3V Analog inputs to XADC
 • Raspberry Pi connector
  • 28 Total FPGA I/O (8 shared pins with Pmod
   A port)

Product Specification


ZYNQ XC7Z020-1CLG400C
 • 650MHz dual-core Cortex-A9 processor
 • DDR3 memory controller with 8 DMA channels and
  4 High Performance AXI3 Slave ports
 • High-bandwidth peripheral controllers: 1G Ethernet,
  USB 2.0, SDIO
 • Low-bandwidth peripheral controller:
  SPI, UART, CAN, I2C
 • Programmable from JTAG, Quad-SPI flash,
  and MicroSD card
 • Programmable logic equivalent to Artix-7 FPGA
  • 13,300 logic slices, each with four 6-input LUTs
   and 8 flip-flops
  • 630 KB of fast block RAM
  • 4 clock management tiles, each with a phase
   locked loop (PLL) and mixed-mode clock
   manager (MMCM)
  • 220 DSP slices
  • On-chip analog-to-digital converter (XADC)
Memory
 • 512MB DDR3 with 16-bit bus @ 1050Mbps
 • 16MB Quad-SPI Flash with factory programmed
  48-bit globally unique EUI-48/64™ compatible
  identifier
 • MicroSD slot
Power
 • Powered from USB or 7V-15V external power source
USB and Ethernet
 • Gigabit Ethernet PHY
 • Micro USB-JTAG Programming circuitry
 • Micro USB-UART bridge
 • USB 2.0 OTG PHY (supports host only)
Audio and Video
 • HDMI sink port (input)
 • HDMI source port (output)
 • I2S interface with 24bit DAC with 3.5mm TRRS jack
 • Line-in with 3.5mm jack
Switches, Push-buttons and LEDs
 • 4 push-buttons
 • 2 slide switches
 • 4 LEDs
 • 2 RGB LEDs
Expansion Connectors
 • Two standard Pmod ports
  • 16 Total FPGA I/O (8 shared pins with
   Raspberry Pi connector)
 • Arduino Shield connector
  • 24 Total FPGA I/O
  • 6 Single-ended 0-3.3V Analog inputs to XADC
 • Raspberry Pi connector
  • 28 Total FPGA I/O (8 shared pins with Pmod
   A port)



Downloads


• PYNQ-Z2 User Manual (PDF)
• PYNQ-Z2 Boot Image
• PYNQ-Z2 Board File (for Pmod IP support please refere here)
• Master XDC
• Protective Acrylic Case (PDF)
• Zynq Datasheet (PDF)
• Zynq Manual (PDF)
• Schematics (PDF)


Downloads


• PYNQ-Z2 User Manual (PDF)
• PYNQ-Z2 Boot Image
• PYNQ-Z2 Board File (for Pmod IP support please refere here)
• Master XDC
• Protective Acrylic Case (PDF)
• Zynq Datasheet (PDF)
• Zynq Manual (PDF)
• Schematics (PDF)


Ordering


PYNQ-Z2 board 1M4-M000127000
PYNQ-Z2 board + Basic Accessories 1M1-M000127DVB
PYNQ-Z2 board + Advanced Accessories 1M1-M000127DVA
Basic Accessories 1M1-M000127001
Advanced Accessories 1M1-M000127002

Technical Support


For Technical Inquiries Regarding TUL PYNQ-Z2
technicalsupport@tul.com.tw



Ordering


PYNQ-Z2 board 1M4-M000127000
PYNQ-Z2 board + Basic Accessories 1M1-M000127DVB
PYNQ-Z2 board + Advanced Accessories 1M1-M000127DVA
Basic Accessories 1M1-M000127001
Advanced Accessories 1M1-M000127002



Technical Support


For Technical Inquiries Regarding TUL PYNQ-Z2
technicalsupport@tul.com.tw



Distribution Partners



Europe Region
Web Site: https://uk.farnell.com/

NA Region
Web Site: https://www.newark.com/

APAC Region
Web Site: https://sg.element14.com/

E-Elements Technology Co., Ltd
Web Site: http://www.e-elements.com/
Newegg
Web Site: http://www.newegg.com/
PChome
Web Site: http://www.pcstore.com.tw/



Distribution Partners


˄